All-Terrain Lawn Tractor Forum

Like riding lawn tractors through mud, woods, rocks, and snow? Then this is the place for you! Share your ideas, Post your projects and more!
 
PortalHomeSearchRegisterLog in
Welcome to the All Terrain Lawn Tractor Forum!
2019 Build Off Underway!

Share
 

 Murraymountain's Mountain Murray [2019 Build-Off Entry]

Go down 
Go to page : Previous  1, 2, 3, 4, 5, 6, 7, 8, 9  Next
AuthorMessage
Murraymountain
Master
Master


Join date : 2019-02-04
Posts : 932

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitimeThu Sep 12, 2019 9:54 am

@MightyRaze wrote:
Hopefully in your area.  No luck here.  I ordered some for my old mst back in the day but came with the wrong OD.   Dizzy

Haha, ain't that how it always happens.
Back to top Go down
Murraymountain
Master
Master
Murraymountain

Join date : 2019-02-04
Posts : 932
Forum Rep : 40
Location : North Carolina

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitimeMon Sep 16, 2019 1:16 pm

So, just to clarify everything, I need a 19.05x40x12mm bearing?
Back to top Go down
Murraymountain
Master
Master
Murraymountain

Join date : 2019-02-04
Posts : 932
Forum Rep : 40
Location : North Carolina

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitimeWed Sep 18, 2019 8:34 pm

Alright, so I went ahead and ordered the bearings. Also ordered a gas pedal, bought a bunch of lights, and a lot of other stuff I'm not gonna mention until it's been done.
Back to top Go down
Murraymountain
Master
Master
Murraymountain

Join date : 2019-02-04
Posts : 932
Forum Rep : 40
Location : North Carolina

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitimeThu Sep 19, 2019 8:21 pm

Well, the new headlight lens came in along with the gas pedal! Soon as I got all the junk out of the box I was able to fill it all the way with the MM's parts.

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 P1110813

NOS clutch (Of my red one)
Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 P1110811

All the lights (except the 2 that're already on it)
Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 P1110812

Just for plain fun, I got me a horn, and an audio system, I hate boring mowers.
Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 P1110814

A big strength factor, the replacement for crappy self-tapping bolts
Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 P1110816

New gas pedal and tow hooks
Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 P1110815

New lens. This is the layout of the headlights... Orange at the ends, light bar in the middle...
Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 P1110817

Transaxle bearings, and a 2500lb winch is also on the way! I get the MM back on Thursday! I've put well over 100 bucks in 'er this week... She better preform good! It was a lot faster than I remembered when I raced down the road beside the fab shop yesterday so, I can't wait to get back to work on 'er!
Back to top Go down
Rerun
Forum Newbie
Forum Newbie


Join date : 2019-04-19
Posts : 46
Forum Rep : 0
Location : Florida

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitimeThu Sep 19, 2019 9:42 pm

Gotta love new parts...like Christmas time. Following to see how it turns out.
Back to top Go down
Murraymountain
Master
Master
Murraymountain

Join date : 2019-02-04
Posts : 932
Forum Rep : 40
Location : North Carolina

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitimeFri Sep 20, 2019 10:30 am

For sure! Got a push button coming in for the horn today, so is the winch, and I believe the bearings are too!
Back to top Go down
Murraymountain
Master
Master
Murraymountain

Join date : 2019-02-04
Posts : 932
Forum Rep : 40
Location : North Carolina

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitimeMon Sep 23, 2019 7:28 pm

Well, everything is in... We tested the bearings on my brother's MST since it was already opened up, and they fit perfect. The winch looks a little complicated to wire up, but I'll get it! Thursday's 3 days away, and I get to do some welding on it then too, so, yeah, I'm ready to get this thing done!
Back to top Go down
MightyRaze
Administrator
Administrator
MightyRaze

Age : 44
Join date : 2016-09-06
Posts : 5895
Forum Rep : 413
Location : Shawnee, OK

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitimeMon Sep 23, 2019 8:51 pm

You winch come with the wiring harness? Is it a remote style? It shouldn't be too bad.

_______________________________________________
Patriot [2019 Build Off]
Kal-El [2018 3rd Place]
Sasquatch II [2017 Finalist]
Li'l Red Murray
Li'l Red 2.0

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Admins10
Back to top Go down
http://mightyraze.com
Murraymountain
Master
Master
Murraymountain

Join date : 2019-02-04
Posts : 932
Forum Rep : 40
Location : North Carolina

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitimeMon Sep 23, 2019 9:42 pm

Yep. It's the 2500lb $60 HF one, I just happened to get it for $30 since I had a 20% off coupon and a $30 gift card. Same as the one on Red and Patriot I believe. This is my first time dealing with a winch, so it probably just looks complicated. I'll get sorted out.
Back to top Go down
MightyRaze
Administrator
Administrator
MightyRaze

Age : 44
Join date : 2016-09-06
Posts : 5895
Forum Rep : 413
Location : Shawnee, OK

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitimeMon Sep 23, 2019 10:00 pm

Its easy. 2 wires to battery, 2 wires to winch.

_______________________________________________
Patriot [2019 Build Off]
Kal-El [2018 3rd Place]
Sasquatch II [2017 Finalist]
Li'l Red Murray
Li'l Red 2.0

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Admins10
Back to top Go down
http://mightyraze.com
Murraymountain
Master
Master
Murraymountain

Join date : 2019-02-04
Posts : 932
Forum Rep : 40
Location : North Carolina

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitimeTue Sep 24, 2019 7:21 pm

Okay great! I just have to make a mounting plate for it, and then I'll wire it in when I wire everything else. There is SOOOOOO much wiring to do.

Well, got me a pulley at TSC today. I may have some trouble with putting steel pulleys on my new clutch... Not enough room between the pulley and the guard (not removable in any way). Horn doesn't sound as good as I thought... I may take it back and get a "low" tone horn.

Some good news, I found a 14 HP Kohler Command with a fuel pump, hydraulic valve lifters, full pressure lubricated, and all for $30 bucks! Everything comes with it. It needs a coil and probably carb, but I have both of those. Only things are, 1) if I can get the guy to respond, 2) if he'll meet me halfway with it since he's a little too far to pick it up (70 miles one way, and all curves). But if I can get my hands on that, I'm in good shape! We'd also get his complete Briggs oppy for another $30.
Back to top Go down
Murraymountain
Master
Master
Murraymountain

Join date : 2019-02-04
Posts : 932
Forum Rep : 40
Location : North Carolina

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitimeThu Sep 26, 2019 10:47 pm

Alrighty, so we FINALLY got the darn thing back.... It's crunch time now. Every time Mighty mentions "60 days and counting" I start sweating lol!. Oh, I also added a spark plug to the "mod" box... Can anyone tell me what I have in mind? Smile

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 P1110821

It's really starting to look like the picture I drew in February!

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 P1110822

I gotta say, the scoop came out pretty darn good...

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 P1110820

Tool box... I still have to mount the lid. I actually welded the hinges on... One came out pretty good for a beginner, but the other was done in true beginner style LOL.

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 P1110824

Unfinished skid plate...

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 P1110823

And now I have to add everything in the box.... That'll take a while. Lotta clean up to do too. I have to do some caulking where the welds are to make it look "complete", the old louvers in the hood haven't been completely taken care of, some welds on the body still need to be ground down, the hood doesn't clear the brush guard, transaxle still leaks, engine still runs crappy, brakes are not there for some reason, tries to go when in gear while the clutch is depressed, exhaust has a bad leak up front... I may just take tomorrow to get 'er running good enough to drive for a couple hours, romp it hard, and then I'll tear into all that....

Looks like we're gonna end up with the engines after all! I'm not gonna beat this engine too hard, so that way I can use it in another mower. If I get it, it will be running on the Kohler by the end of the build off. Oh, and it looks like the motors aren't gonna cost anything! We're doing a flat out trade for an electric lift chair. It'll work out great on both ends, so I don't see any reason why we can't make it happen!

I was able to drive it down a two lane a bit today too. I think I'm satisfied with the ratio I'm running.... Not too fast, not too slow.

Whaya think?
Back to top Go down
MightyRaze
Administrator
Administrator
MightyRaze

Age : 44
Join date : 2016-09-06
Posts : 5895
Forum Rep : 413
Location : Shawnee, OK

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitimeThu Sep 26, 2019 11:36 pm

Looking at your brake in that one pic. Looks like they are all the way engaged? Maybe parking brake on. As for brakes, there are 2 bolts and a nut in the center. I would start with the 2 bolts. This will allow the caliper to come off so you can check the brake pads. One in the caliper and one under the disk. They could be worn out. Mine were. While you have it out check to see if the 2 little metal pins/barrels can fall out and not frozen.

**If they are frozen, go ahead and take the nut off and you can knock those through and clean the passages and the pins. They should be free. Coat them with anti-seize when reinstalling.

If the pins move free and the pads were OK, put the caliper back on the transaxle like it was. If still no brakes, set the parking brake. Move the tractor back and forth while tightening that center nut a little bit at a time. When the brakes finally catch, I typically turn the nut about another 1/4 turn to tighten. Test. If too tight, back it off a tiny bit till desired.

Another possible issue, someone took the brake lever off and has it on backwards. With the lever upright, the 2 pins should be cupped and not on the ridge of the lever.

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 06261710

_______________________________________________
Patriot [2019 Build Off]
Kal-El [2018 3rd Place]
Sasquatch II [2017 Finalist]
Li'l Red Murray
Li'l Red 2.0

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Admins10
Back to top Go down
http://mightyraze.com
Murraymountain
Master
Master
Murraymountain

Join date : 2019-02-04
Posts : 932
Forum Rep : 40
Location : North Carolina

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitimeFri Sep 27, 2019 11:59 am

I redid the brakes before the build off started. They were one of the worst sets I've seen yet. I'll be putting a dash light on the mower to indicate the parking brake being on because I've driven it a lot without releasing the brake. The brakes have to be burnt up by now, so I will be replacing those, but these will do for now if I can get them to work. It does looks like someone put that piece on backwards now that I think about it... Might have to drill a new hole and flip it around when I get some time to work on it. It seemed to have more brakes when the brakes were disengaged... scratch
Back to top Go down
MightyRaze
Administrator
Administrator
MightyRaze

Age : 44
Join date : 2016-09-06
Posts : 5895
Forum Rep : 413
Location : Shawnee, OK

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitimeFri Sep 27, 2019 4:06 pm

Shouldn't need to drill a hole. Just unto the center nut and flip it over. But like you said, the pads are probably shot by now.

_______________________________________________
Patriot [2019 Build Off]
Kal-El [2018 3rd Place]
Sasquatch II [2017 Finalist]
Li'l Red Murray
Li'l Red 2.0

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Admins10
Back to top Go down
http://mightyraze.com
Murraymountain
Master
Master
Murraymountain

Join date : 2019-02-04
Posts : 932
Forum Rep : 40
Location : North Carolina

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitimeFri Sep 27, 2019 6:41 pm

Well, after I flip it around I meant. It's actuated by a steel rod now, so it's not adjustable. And when I flip it around, the hole will be further back, so I may or may not have to drill it. I noticed that I have brakes when half way engaged, but not when all the way forward. We'll see what happens I guess. Right now I just need it to run. I'm tired of this engine. Can't wait till I get that Kohler!
Back to top Go down
Murraymountain
Master
Master
Murraymountain

Join date : 2019-02-04
Posts : 932
Forum Rep : 40
Location : North Carolina

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitimeSun Sep 29, 2019 10:22 am

Well, got it running right finally. Needed a spark plug LOL. Anyway, the gas pedal setup has to go. It's just all around too dangerous. I watched a video in another thread that showed a simple front axle locker, so I'm gonna do that too. Next week is break week for me, so my goal is to have the trans out, apart, do the repairs and upgrades, and have it moving under it's own power by the end of that week. Anyway, here's some videos from yesterday...

MM running
Top speed run
Drifting fail
Back to top Go down
MightyRaze
Administrator
Administrator
MightyRaze

Age : 44
Join date : 2016-09-06
Posts : 5895
Forum Rep : 413
Location : Shawnee, OK

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitimeSun Sep 29, 2019 12:26 pm

Good thing that didn't happen during the top speed run.

_______________________________________________
Patriot [2019 Build Off]
Kal-El [2018 3rd Place]
Sasquatch II [2017 Finalist]
Li'l Red Murray
Li'l Red 2.0

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Admins10
Back to top Go down
http://mightyraze.com
Murraymountain
Master
Master
Murraymountain

Join date : 2019-02-04
Posts : 932
Forum Rep : 40
Location : North Carolina

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitimeSun Sep 29, 2019 1:13 pm

Heh, that's for sure. I cut that slot a little deep, so the clip fell off. I put a Craftsman cover over it so it doesn't happen again.
Back to top Go down
Murraymountain
Master
Master
Murraymountain

Join date : 2019-02-04
Posts : 932
Forum Rep : 40
Location : North Carolina

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitimeSun Sep 29, 2019 4:57 pm

Well, started wrenching on 'er again today... Got some stuff accomplished. Could've done more but I'm tired and about done in for the day. So anyway, I had to change over to longer hood mounts since I barely had any room to do anything in the front.

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 P1110830

Then I mounted the horn...

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 P1110829

Moved the solenoid...

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 P1110831

Ground down these welds...

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 P1110833

And this is what I'm using for the headlight mounts...

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 P1110832

I'm just gettin' started here too. I'll get more done Tuesday afternoon.
Back to top Go down
Rerun
Forum Newbie
Forum Newbie


Join date : 2019-04-19
Posts : 46
Forum Rep : 0
Location : Florida

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitimeSun Sep 29, 2019 7:40 pm

Liking what you done so far. Welding a plate in the deck lift hole was a great idea.
Back to top Go down
Murraymountain
Master
Master
Murraymountain

Join date : 2019-02-04
Posts : 932
Forum Rep : 40
Location : North Carolina

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitimeSun Sep 29, 2019 7:47 pm

Yeah it came out pretty nice actually. It just needs paint now.
Back to top Go down
Murraymountain
Master
Master
Murraymountain

Join date : 2019-02-04
Posts : 932
Forum Rep : 40
Location : North Carolina

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitimeWed Oct 02, 2019 9:43 am

So, as of Monday, I managed to get a little more done!

Took the front end apart and cleaned up all the rust (still a little resistant, but way better)...

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 P1110835

Also got the front light bar mounted (now I have to mount it to the hood Rolling Eyes)...

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 P1110834

And I cut the lip on the engine plate off, and moved the new hood mounts downward just a hair. I also replaced the self-tapping bolts on the front end since I already had it apart...

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 P1110836


Now I have a question... How can I turn a safety switch into a light activating switch? In other words, can it be used like a push button?
Back to top Go down
MightyRaze
Administrator
Administrator
MightyRaze

Age : 44
Join date : 2016-09-06
Posts : 5895
Forum Rep : 413
Location : Shawnee, OK

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitimeWed Oct 02, 2019 10:36 am

Absolutely.  I use to use the clutch safety switch to activate brake lights for a while on Red and my Sasquatch II build.




I have since ripped both of them out.  LOL

_______________________________________________
Patriot [2019 Build Off]
Kal-El [2018 3rd Place]
Sasquatch II [2017 Finalist]
Li'l Red Murray
Li'l Red 2.0

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Admins10
Back to top Go down
http://mightyraze.com
Murraymountain
Master
Master
Murraymountain

Join date : 2019-02-04
Posts : 932
Forum Rep : 40
Location : North Carolina

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitimeWed Oct 02, 2019 10:39 am

Awesome! Which wires am I supposed to use?
Back to top Go down
MightyRaze
Administrator
Administrator
MightyRaze

Age : 44
Join date : 2016-09-06
Posts : 5895
Forum Rep : 413
Location : Shawnee, OK

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitimeWed Oct 02, 2019 10:54 am

That you will just have to play with a multimeter or test light.  Like on my Murray, it had 4 wires.  2 on when depressed 2 off. The pairs would be opposite when not pushed down.  On the craftsman, I only had 2 wires.  Like I mentioned, you just have to figure it out.  Also, if you want "brake" lights and regular lights on the same circuit, you will need to introduce a diode in there to keep the power back-feeding.  Easier to have them separate.

_______________________________________________
Patriot [2019 Build Off]
Kal-El [2018 3rd Place]
Sasquatch II [2017 Finalist]
Li'l Red Murray
Li'l Red 2.0

Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Admins10
Back to top Go down
http://mightyraze.com
Sponsored content




Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Empty
PostSubject: Re: Murraymountain's Mountain Murray [2019 Build-Off Entry]   Murraymountain's Mountain Murray [2019 Build-Off Entry] - Page 7 Icon_minitime

Back to top Go down
 
Murraymountain's Mountain Murray [2019 Build-Off Entry]
Back to top 
Page 7 of 9Go to page : Previous  1, 2, 3, 4, 5, 6, 7, 8, 9  Next
 Similar topics
-
» Mickee's Huge Migraine [2017 Build-Off Entry]
» Murray Street Mower
» Price quote to build a racing mower
» BackWoods Murray Build
» Craftsman GT16 build

Permissions in this forum:You cannot reply to topics in this forum
All-Terrain Lawn Tractor Forum :: Build-Off Competition :: Build-Off Competition Threads-
Jump to: